Lever Pump

Lever Pump portable, manually-operated actuator

portable mechanical advantage

The Waterra Lever Pump is a manual lever designed to provide operators with a convenient, portable mechanism which would provide some mechanical advantage when manually operating the Inertial Pump as well as facilitating the collection of samples with this system.

This actuator will fasten onto most above ground well completions quickly and easily. The tubing clamp is designed to accept Standard Flow, High Flow and Low Flow tubing and the handle is adjustable in order to accommodate various casing diameters and desired stroke lengths.

The Lever Pump weighs approximately 8 pounds.


This actuator is the best choice for the occasional light duty user of the Waterra Inertial Pumping System (Standard Flow, High Flow and Low Flow).


MANUAL

Link to the Hydrolift-2 Owner's Manual
LEVER PUMP SPECIFICATIONS
Dimensions 24" length, 17" height
Weight 8 lbs (3.6 kg)
Powered by Manual operation
Additional Requirements Above ground well completion
For Use with Inertial Pumping Systems — Standard Flow, High Flow, Low Flow

FEATURES

  • fully adjustable
    The Lever pump is fully adjustable and will adapt to almost any size casing or protective well casing. An above ground well completion is required in order to use the Lever Pump.
  • one handed operation
    Using the Lever Pump can make sample collection easier because it supports the discharge end of the pump's tubing, allowing the field technician to operate the inertial pump with one hand and hold a sample container with the other.
Closeup of the hinged tubing clamp on the Lever Pump
  • hinged tubing clamp
    The tubing clamp is hinged, which helps prevent pump tubing from abrading against well casing.
  • reduces fatigue
    The hand pump can reduce some of the fatigue that one may experience when required to purge large volumes from wells.
  • suitable for use with Standard Flow, High Flow and Low Flow Inertial Pumps
  • adapts to almost any size casing or protective well casing

Hydrolift-2


high performance automation

The Hydrolift-2 is a portable, electrically operated device that is used to automate the operation of the Inertial Pump. The Hydrolift is powered by a 3/4 horsepower electric motor (available in either 110 volt or 220 volt) and generates a 4 inch stroke at up to 200 cycles per minute. The Hydrolift II weighs only 35 pounds and requires an electrical power supply of at least 1000 watts.

Using the Hydrolift-2 will result in a big boost to your field sampling program. This actuator is perfect for purging and sampling 2” diameter monitoring wells up to 150 to 200 feet deep. This actuator is optimized to operate with the Standard Flow System up to its maximum effective depth and will operate with the High Flow System up to a depth of 150 feet.


This actuator is the ideal choice for the frequent user of the Waterra Inertial Pumping System with moderate to extreme pumping requirements (Standard Flow, High Flow and Low Flow).


EXPLODED DIAGRAM & PARTS LIST

link to Hydrolift-2 Exploded Diagram and Parts List pdf


MANUAL

Link to the Hydrolift-2 Owner's Manual
HYDROLIFT-2 SPECIFICATIONS
Dimensions 15" length, 20" height, 7" width (38cm L x 51cm H x 18cm W)
Weight 38 lbs (17.25 kg)
Powered by 3/4 hp (6 amps) volt DC electric motor
Performance Characteristics Generates a 4" stroke,
adjustable 0—180 cycles/min
Additional Requirements 110 VAC or 220 VAC power supply
For Use With Inertial Pumping Systems — Standard Flow, High Flow, Low Flow

FEATURES

  • fully adjustable — the Hydrolift-2 is fully adjustable and will adapt to almost any size casing or protective well casing and can also be used with flush grade well completions.
  • anchored discharge end of tubing — the Hydrolift-2 supports the inertial pump tubing and also anchors the discharge end of the tubing facilitating sample collection.
  • requires either a 110 volt or 220 volt AC power supply.
  • great for use when developing monitoring wells
  • reduces fatigue — the use of an automated Waterra actuator will eliminate the fatigue that can be experienced on large monitoring programs.
  • hinged tubing clamp
  • suitable for use with Standard Flow, High Flow and Low Flow Inertial Pumps
  • adapts to almost any size casing or protective well casing

RENTAL PROGRAM

Would you like to try a Hydrolift? Both Canadian and US offices maintain a fleet of Hydrolift-2s available for both short and long term rentals, beginning with a 2 day minimum rental period. You are not billed for time in transit though you would be expected to pay shipping costs in both directions. Please call for pricing.

PowerPack PP1


PowerPack PP1

power & portability

The Waterra PowerPack PP1 provides the mechanical actuation for pumping with inertial pumps to depths of over 60m, in a fully portable, single operator power unit. At 13 kg, the PowerPack PP1 provides outstanding pumping performance.

The PP1 is powerful enough to lift water from over 60m depth using the Standard Flow System, and is so compact that it fits onto a back-pack frame. The PowerPack PP1 incorporates clamps for Waterra High Flow and Standard tubing sizes (adaptors are available for smaller tubes).

A Honda GX-25 series, 1.0 horsepower, 4 stroke, gasoline motor powers this device, which can run for approximately 1 hour without refuelling.

PP1/BP — PowerPack PP1 including backpack and spark arrestor


This gasoline powered automatic actuator is for use with the Waterra Inertial Pumping System (Standard Flow, High Flow and Low Flow).

It is an excellent choice for those with moderate pumping requirements.


EXPLODED DIAGRAM & PARTS LIST

Link to the PowerPack PP1 Exploded Diagram

POWERPACK-PP1 SPECIFICATIONS
Dimensions 15.5" length, 22.5" height, 14.5" width
(39cm L x 57cm H x 37cm W)
Weight 28.6 lbs (13kg)
Powered by Honda GX25 (25cc Mini 4-Stroke OHC gasoline engine)
Performance Characteristics Generates a 4" stroke,
adjustable 0—140 cycles/min
Additional Requirements Regular gasoline, SAE 10W-30 motor oil
For Use With Inertial Pumping Systems — Standard Flow, High Flow, Low Flow

FEATURES

  • fully adjustable and will adapt to almost any size casing or protective well casing and can also be used with flush grade well completions.
  • anchored discharge end of tubing facilitates sample collection — the PowerPack-PP1 supports the inertial pump tubing and also anchors the discharge end of the tubing facilitating sample collection.
  • powered by the Honda GX25 a 25cc Mini 4-Stroke OHC gasoline engine — this lightweight motor is EPA/CARB compliant, runs on regular gas and has a quiet - pleasing "low" tone.
  • includes a backpack frame making it completely portable. Using the PowerPack-PP1 will result in a big boost to your field sampling program.
  • perfect for purging and sampling 2” diameter monitoring wells up to 150-200 feet deep. This actuator is also great for use when developing monitoring wells.
  • eliminates the fatigue that can be experienced on large monitoring programs.
  • adapts to almost any size casing or protective well casing

PowerPump-2


PowerPump-2

power & endurance

The Waterra PowerPump-2 is the most powerful pump actuator manufactured by Waterra. A Honda GX100, 3 horsepower, 4 stroke, gasoline motor powers this device.

This actuator generates a 6 inch stroke and can operate both the Standard Flow System and High Flow System to their maximum effective depths. The PowerPump 2 weighs 70 pounds and usually requires two people to carry it.


This actuator is a gasoline powered automatic actuator for use with the Waterra Inertial Pumping System (Standard Flow, High Flow and Low Flow).

It is an excellent choice for those with extreme pumping requirements.


EXPLODED DIAGRAM & PARTS LIST


MANUAL

Link to the PowerPump-2 Owner's Manual
POWERPUMP-2 SPECIFICATIONS
Dimensions 29" length, 30" height, 12" width (74cm L x 76cm H x 30cm W)
Weight 75 lbs (34 kg)
Powered by Honda GX100 Air-cooled, 4-Stroke OHC gasoline engine
Performance Characteristics Generates a 6" stroke,
adjustable 0—150 cycles/min
Additional Requirements Regular gasoline, SAE 10W-30 motor oil
For Use With Inertial Pumping Systems — Standard Flow, High Flow, Low Flow

FEATURES

  • fully adjustable — the PowerPump-2 is adjustable and will adapt to almost any size casing of protective well casing and can also be used with flush grade well completions.
  • supported tubing & anchored discharge end of tubing facilitates sample collection
  • powered by Honda GX100 Air-cooled, 4-Stroke, OHC gasoline engine —this 2.8 hp motor is EPA/CARB compliant and runs on regular gas.
  • our most powerful actuator — it can operate the High Flow inertial pump in monitoring wells to depths of up to 300 feet. Using the PowerPump-2 will result in a big boost to your field sampling program, especially at sites with very deep installations.
  • adapts to almost any size casing or protective well casing — this actuator is perfect for purging and sampling 2” diameter monitoring wells up to 300 feet deep. This actuator is also great for use when developing monitoring wells.
  • reduces fatigue when purging large volumes from wells — the use of an automated Waterra actuator will eliminate the fatigue that can be experienced on large monitoring programs.