portable mechanical advantage

The Waterra Lever Pump was designed to provide operators with a convenient, portable mechanism which would provide some mechanical advantage when manually operating the Inertial Pump as well as facilitating the collection of samples with this system.

This actuator will fasten onto most above ground well completions quickly and easily. The tubing clamp is designed to accept both Standard Flow and High Flow tubing and the handle is adjustable in order to accommodate various casing diameters and desired stroke lengths. The Lever Pump weighs approximately 7 pounds.

features

The Waterra Lever Pump is a manual lever suitable for use with the Standard Flow, High Flow and Low Flow Waterra Inertial Pumping Systems.

The Lever pump is fully adjustable and will adapt to almost any size casing or protective well casing. An above ground well completion is required in order to use the Lever Pump.

Using the Lever Pump can make sample collection easier because it supports the discharge end of the pump's tubing, allowing the field technician to operate the inertial pump with one hand and hold a sample container with the other. The tubing clamp is hinged, which helps prevent pump tubing from abrading against well casing.

Additionally, the hand pump can reduce some of the fatigue that one may experience when required to purge large volumes from wells.

high performance automation

The Hydrolift-2 is a portable, electrically operated device that is used to automate the operation of the Inertial Pump. The Hydrolift is powered by a 3/4 horsepower electric motor (available in either 110 volt or 220 volt) and generates a 4 inch stroke at up to 200 cycles per minute. The Hydrolift II weighs only 35 pounds and requires an electrical power supply of at least 1000 watts.

This actuator is optimized to operate with the Standard Flow System up to its maximum effective depth and will operate with the High Flow System up to a depth of 150 feet.

This actuator is the ideal choice for the frequent user of the Inertial Pumping System with moderate to extreme pumping requirements.

features

The Waterra Hydrolift-2 is an electrically powered automatic actuator for use with the Standard Flow, High Flow and Low Flow Waterra Inertial pumping systems.

The Hydrolift-2 is fully adjustable and will adapt to almost any size casing or protective well casing and can also be used with flush grade well completions. The Hydrolift-2 supports the inertial pump tubing and also anchors the discharge end of the tubing facilitating sample collection.

The Waterra Hydrolift-2 requires either a 110 volt or 220 volt AC power supply. Using the Hydrolift-2 will result in a big boost to your field sampling program. This actuator is perfect for purging and sampling 2” diameter monitoring wells up to 150 to 200 feet deep.

This actuator is also great for use when developing monitoring wells. The use of an automated Waterra actuator will eliminate the fatigue that can be experienced on large monitoring programs.

rental program

 

Would you like to try a Hydrolift?

 

 

exploded diagram & parts list

 

 

 

 

 

 

product manual

 

 

 

 

 

 

 

durable & lightweight

The New Waterra PowerLift-3 is a powerful portable actuator with the durability of the Waterra Power Pump-2's mechanism and the light weight of the Hydrolift-2's motor, gear and control. The Waterra PowerLift-3 can operate the inertial pumping system in almost any well system, speeding up purging and sampling, saving time and money.

This actuator can operate the Standard Flow System up to its maximum effective depth and will operate the and High Flow System up to a depth of 150 feet.The PowerLift-3 weighs 45lbs (20kg) and requires a 110 AC power source with a minimum of 1500 watts.

This actuator is the ideal choice for the frequent user of the Inertial Pumping System with moderate to extreme pumping requirements.

features

The Waterra PowerLift-3 is an electrically powered automatic actuator for use with the Standard Flow System, High Flow System and Low Flow Waterra Inertial Pumping systems.

The PowerLift-3 is fully adjustable and will adapt to almost any size casing of protective well casing and can also be used with flush grade well completions. The PowerLift-3 supports the inertial pump tubing and also anchors the discharge end of the tubing, facilitating sample collection.

The Waterra PowerLift-3 requires either a 110 volt or 220 volt AC power supply. Using the PowerLift-3 will result in a big boost to your field sampling program.

This actuator is perfect for purging and sampling 2” diameter monitoring wells up to 200 feet deep. This actuator is also great for use when developing monitoring wells. Although the PowerLift-3 weighs more than the Hydrolift-2, it generates a 50% longer stroke than the Hydrolift-2. The longer 6” stroke produces a better performance in deeper piezometers.

The use of an automated Waterra actuator will eliminate the fatigue that can be experienced on large monitoring programs.

power & portability

The Waterra PowerPack PP1 provides the mechanical actuation for pumping with inertial pumps to depths of over 60m, in a fully portable, single operator power unit. At 13 kg, the PowerPack PP1 provides outstanding pumping performance.

The PP1 is powerful enough to lift water from over 60m depth using the Standard Flow System, and is so compact that it fits onto a back-pack frame. The PowerPack PP1 incorporates clamps for Waterra High Flow and Standard tubing sizes (adaptors are available for smaller tubes).

A Honda GX-22 series, 0.25 horsepower, 4 stroke, gasoline motor powers this device, which can run for approximately 1 hour without refuelling.

 

PP1/BP — PowerPack PP1 including backpack and spark arrestor

features

The Waterra PowerPack-PP1 is a gasoline powered automatic actuator for use with the Standard Flow System, High Flow System and Low Flow Waterra Inertial Pumping systems.

The PowerPack-PP1 is fully adjustable and will adapt to almost any size casing or protective well casing and can also be used with flush grade well completions. The PowerPack-PP1 supports the inertial pump tubing and also anchors the discharge end of the tubing facilitating sample collection.

The Waterra PowerPack-PP1 is powered by the Honda GX25 a 25cc Mini 4-Stroke OHC gasoline engine. This lightweight motor is EPA/CARB compliant, runs on regular gas and has a quiet - pleasing "low" tone. The PowerPack PP1 includes a backpack frame making it completely portable. Using the PowerPack-PP1 will result in a big boost to your field sampling program.

This actuator is perfect for purging and sampling 2” diameter monitoring wells up to 150-200 feet deep. This actuator is also great for use when developing monitoring wells.

The use of an automated Waterra actuator will eliminate the fatigue that can be experienced on large monitoring programs.

power & portability

The Waterra PowerPump-2 is the most powerful pump actuator manufactured by Waterra. A Honda GX100, 3 horsepower, 4 stroke, gasoline motor powers this device.

This actuator generates a 6 inch stroke and can operate both the Standard Flow System and High Flow System to their maximum effective depths. The PowerPump 2 weighs 70 pounds and usually requires two people to carry it.

features

The Waterra PowerPump-2 is a gasoline powered automatic actuator for use with the Standard Flow System, High Flow System and Low Flow Waterra Inertial Pumping systems.

The PowerPump-2 is adjustable and will adapt to almost any size casing of protective well casing and can also be used with flush grade well completions. The PowerPump-2 supports the inertial pump tubing and also anchors the discharge end of the tubing, facilitating sample collection.

The Waterra PowerPump-2 is powered by the Honda GX100 Air-cooled, 4-Stroke, OHC gasoline engine. This 2.8 hp motor is EPA/CARB compliant, runs on regular gas. The PowerPump-2 is our most powerful actuator and can operate the High Flow inertial pump in monitoring wells to depths of up to 300 feet. Using the PowerPump-2 will result in a big boost to your field sampling program, especially at sites with very deep installations.

This actuator is perfect for purging and sampling 2” diameter monitoring wells up to 300 feet deep. This actuator is also great for use when developing monitoring wells.

The use of an automated Waterra actuator will eliminate the fatigue that can be experienced on large monitoring programs.

product manual